June 27 Shijiazhuang Steel Market Price Quotes

Product Name Specification Material Steel Factory/Origin Price (Yuan/Ton) Than Yesterday Last Week, General Line Φ6.5/8mm Q235 Handan Steel 5730 0 30 -120 High Line Φ6.5/8mm Q235 Handan Steel 5830 0 30 - 120 High Line Φ6.5/8mm Q235 Shougang 5830 0 30 -120 High Line Φ6.5/8mm Q235 Xing Steel 5830 0 30 -120 Rebar Φ12mm HRB335 Handan Steel 5830 0 30 -120 Rebar Φ12mm HRB335 Emerging Cast Pipe 5800 0 0 -150 Rebar Φ14mm HRB335 Rebar 5750 0 0 -150 Rebar Φ16-25mm HRB335 Rebar 5600 0 0 -150 Rebar Φ16-25mm HRB335 Emerging Cast Pipe 5550 0 0 -200 Rebar Φ16-25mm HRB335 Dedicated 5660 0 0 -90 Rebar Φ12mm HRB400 Bearing Steel 5810 0 0 -120 Rebar Φ16-25mm HRB400 Bearing Steel 5660 0 0 -120 Rebar Φ16-25mm HRB400 Dedicated 5660 0 -20 -190 Hot Roll Coil 2.0*1500*c Q235 Handan Steel 6000 0 50 50 Hot Roll Coil 2.75*1500*c Q235 Taigang 5950 0 50 50 Hot Roll Coil 3.0*1500*c Q235 Taigang 6000 50 100 100 Hot Roll Coil 3.0*1500*c Q235 Tang Gang 6000 150 200 100 Hot Roll Coil 4.75*1500*c Q235 Tang Steel 5870 70 120 20 Hot Roll Coil 9.5*1250*c Q235 Tang Steel 5870 70 120 20 Cold Roll Coil 1.0*1000*2000 SPCC Angang 7700 0 0 450 Cold rolled coil 2.0*1000*2000 SPCC Angang 7700 0 0 450 Cold rolled coil 3.0*1000*2000 SPCC Angang 7700 0 0 200 Cold rolled coil 1.0*1000*2000 SPCC Cold rolled steel 7700 0 0 500 Cold rolled Coil 1.0*1000*2000 SPCC Benxi Steel 7700 0 0 500 Puzhong Plate 8mm Q235 Handan Steel/TISCO 6880 0 -60 -20 Puzhong Plate 10mm Q235 Handan Steel 6660 0 -60 -40 Puzhong Plate 12mm Q235 Handan Steel 6440 0 -110 -40 Puzhong Board 16-20mm Q235 Tiangang 6330 0 -60 10 Puzhong Board 14-20mm Q235 Handan Steel 6370 0 -60 -50 Puzhong Board 14-25mm Q235 Wenfeng 6280 0 -60 -40 Puzhong Board 14-25mm Q235 Puyang 6290 0 -60 -30 Puzhong Board 16-25mm Q235 Jingye 6290 0 -60 -30 Puzhong Board 16-28mm Q235 Jingye 6300 0 -60 -20 Low Alloy Board 8mm Q345 Handan Steel 7050 0 -60 -40 Low alloy sheet 14-25mm Q345 Handan steel 6590 0 -60 -40 I beam 25# Q235 Laiwu steel 5400 0 100 100 I beam 32# Q235 Steel packet 6050 0 150 150 Channel steel 16# Q235 Jiang Tian 5420 0 0 -30 Channel 32# Q235 Jiangtian 5300 0 0 0 Angle Steel 5# Q235 Shougang 5580 0 0 -20 Angle Steel 10# Q235 Tang Steel 5600 0 0 0

Excavator cylinder oil seals

â‘ Hardness:

Due to the scientific synthesis of high-molecular polyurethane elastomer materials using iron rubber, the higher the hardness, the higher the modulus, the smaller the elongation, and the better the wear resistance and heat resistance. Well, in the range of minus 35 degrees Celsius to 100 degrees Celsius, and at a pressure of 60 to 70 MPa, the maximum sealing performance can be guaranteed.

â‘¡Pressure resistance:

The use of viscoelastic seals made of nitrile rubber is the most complete protection against damage caused by back pressure. In the range of minus 55 degrees Celsius to 100 degrees Celsius, and under a pressure of 21MPa, due to the rubber The seal is often in a compressed state, so the compression performance of the rubber seal must be considered. It not only achieves enhanced anti-climbing performance and low friction resistance, but also has good performance in dealing with special low-temperature oil, and can also be used in combination with Anti-wear Ring double-purpose retaining ring BRL type.

â‘¢Prevention of oil leakage:

Sealing products made of polytetrafluoroethylene and nitrile rubber/PTFErubber; or seals made of nylon resin and nitrile rubber, which can be used in a wide range of applications with large pressure changes and fast sliding speeds According to the working condition, the input hydraulic pressure cutout is designed on the end face of the polytetrafluoroethylene ring to prevent penetration leakage. The maximum working temperature environment is minus 40 degrees Celsius to 160 degrees Celsius; the maximum working pressure is 50MPa.

SPGW piston seal

Material:PTFE+rubber elastomer+reinforced modified nylon
Temperature:Nitrile rubber -40~100℃
Speed:=1.0m/s
Pressure:≤50mpa

SPGO piston seal

Material:PTFE+rubber elastomer
Temperature:Nitrile rubber -40~110℃
Speed:=1.0m/s
Pressure:≤35mpa

SRUV piston rod seal

Material:NBR+thermoplastic polyurethane
Temperature: -35`90℃
Speed:=0.5m/s
Pressure:≤40mpa

SRS piston rod seal

Material:PTFE+NBR
Temperature:-40~110℃
Speed:=1.0m/s
Pressure:≤40mpa

SRCB piston rod buffer seal

Material:Polyurethane+modified polyoxymethylene
Temperature: -35~110℃
Speed:=1.0m/s
Pressure:≤50mpa

SRU piston rod seal

Material:Polyurethane
Temperature:-35~100℃
Speed:=1.0m/s
Pressure:≤40mpa

SRD iron case dust prevention

Material:Polyurethane+metal skeleton material
Temperature:-40~110℃
Speed:=1.0m/s

SRDI soft dustproof

Material:polyurethane
Temperature:-40~110℃
Speed:=1.0m/

SDS Dumbbell Seal

Material:polyurethane
Temperature: -35~110℃
Speed:=0.5m/s
Pressure:≤50mpa

SPG piston combination seal

Temperature:

NBR+Polyurethane + Modified Polyoxymethylene

Temperature:-35`110℃

Speed:=0.3m/s

Pressure:≤70mpa

SRNL piston rod seal

Material

NBR+Polyurethane + Modified Polyoxymethylene

Temperature:-35`110℃

Speed:=0.3m/s

Pressure:≤70mpa

SRDF Piston Rod Seal

Material

Polyester rubber

Temperature:-40`100℃

Speed:=1.0m/s

SDY Y-seal

Material:Polyurethane

Temperature:-35~110℃

Speed:=0.5m/s

Pressure:≤70mpa

KZT anti fouling ring

SDS Steffel

Piston main oil seal

oil seals,hydraulic oil seal,track link oil seal,TCV oil seal

Safe Seal Technology Co., Ltd. , https://www.jolseals.com