Small Lab Spray Dryer/Spray Drying Equipment for Pilot

Name: Small lab spray dryer, mini spray dryer, movable pilot spray dryer

Description: OM1500 miniature laboratory spray dryer (device) is a Division I introduce and absorb advanced technology, manufacturing in the country; major components and electrical imports. Machine design compact, portable, self-contained body of the machine, power can be used without auxiliary facilities. PLC control, touch screen display, Chinese and English operation interface.




Details description:
Experimental Spray Dryer Application: mainly used in universities, research institutes and food, biology, beverage, chemical, materials, pharmaceutical and other micro-enterprise development and production laboratories particles, such as the solution to all emulsions, suspensions with a wide spectrum applicability, suitable for drying heat-sensitive materials such as biological products, bio-pesticides, enzymes, etc., because the ejected material only when atomized particle size subjected to high temperatures, it is just an instant heat, can keep these active materials which remain after the drying of the active ingredient from damage.

Experimental Spray Dryer Application: beverages, perfumes and dyes, milk and egg products, plant and vegetable extracts, pharmaceutical synthesis, thermal plastic materials, polymers and resins, aromatics, blood products, ceramics and superconductors, Biochemistry products, dyes, soaps and detergents, food and adhesives, oxides, bone and tooth powder, and so on.




Technical parameters:
The maximum evaporation rate: 2000ML / H
Inlet temperature range: 30 ºC -280 ºC
Air temperature range: 30 ºC -140 ºC
Heating temperature accuracy: ± 1 ºC
Drying time :1.0-1 .5 S
Peristaltic pump feed range :50-2000ML / H
Dry air flow :0-5 .5M3/Min, maximum pressure 686Pa
Spraying gas flow :0-4 .2 M3 / H, spray pressure 2-8Bar
Spray System: with (0.5 - 2.5MM) of two-fluid nozzle
Ejector (Acupuncture) can be automatically adjusted between :0-20S
Spray / hot air flow: in the same direction, down
Heater power: 3KW 220V
Total power: 3.8KW 220V
Size: 1450MM × 650MM × 550MM (H × L × W)
Weight: 110KG
 

Excavator cylinder oil seals

â‘ Hardness:

Due to the scientific synthesis of high-molecular polyurethane elastomer materials using iron rubber, the higher the hardness, the higher the modulus, the smaller the elongation, and the better the wear resistance and heat resistance. Well, in the range of minus 35 degrees Celsius to 100 degrees Celsius, and at a pressure of 60 to 70 MPa, the maximum sealing performance can be guaranteed.

â‘¡Pressure resistance:

The use of viscoelastic seals made of nitrile rubber is the most complete protection against damage caused by back pressure. In the range of minus 55 degrees Celsius to 100 degrees Celsius, and under a pressure of 21MPa, due to the rubber The seal is often in a compressed state, so the compression performance of the rubber seal must be considered. It not only achieves enhanced anti-climbing performance and low friction resistance, but also has good performance in dealing with special low-temperature oil, and can also be used in combination with Anti-wear Ring double-purpose retaining ring BRL type.

â‘¢Prevention of oil leakage:

Sealing products made of polytetrafluoroethylene and nitrile rubber/PTFErubber; or seals made of nylon resin and nitrile rubber, which can be used in a wide range of applications with large pressure changes and fast sliding speeds According to the working condition, the input hydraulic pressure cutout is designed on the end face of the polytetrafluoroethylene ring to prevent penetration leakage. The maximum working temperature environment is minus 40 degrees Celsius to 160 degrees Celsius; the maximum working pressure is 50MPa.

SPGW piston seal

Material:PTFE+rubber elastomer+reinforced modified nylon
Temperature:Nitrile rubber -40~100℃
Speed:=1.0m/s
Pressure:≤50mpa

SPGO piston seal

Material:PTFE+rubber elastomer
Temperature:Nitrile rubber -40~110℃
Speed:=1.0m/s
Pressure:≤35mpa

SRUV piston rod seal

Material:NBR+thermoplastic polyurethane
Temperature: -35`90℃
Speed:=0.5m/s
Pressure:≤40mpa

SRS piston rod seal

Material:PTFE+NBR
Temperature:-40~110℃
Speed:=1.0m/s
Pressure:≤40mpa

SRCB piston rod buffer seal

Material:Polyurethane+modified polyoxymethylene
Temperature: -35~110℃
Speed:=1.0m/s
Pressure:≤50mpa

SRU piston rod seal

Material:Polyurethane
Temperature:-35~100℃
Speed:=1.0m/s
Pressure:≤40mpa

SRD iron case dust prevention

Material:Polyurethane+metal skeleton material
Temperature:-40~110℃
Speed:=1.0m/s

SRDI soft dustproof

Material:polyurethane
Temperature:-40~110℃
Speed:=1.0m/

SDS Dumbbell Seal

Material:polyurethane
Temperature: -35~110℃
Speed:=0.5m/s
Pressure:≤50mpa

SPG piston combination seal

Temperature:

NBR+Polyurethane + Modified Polyoxymethylene

Temperature:-35`110℃

Speed:=0.3m/s

Pressure:≤70mpa

SRNL piston rod seal

Material

NBR+Polyurethane + Modified Polyoxymethylene

Temperature:-35`110℃

Speed:=0.3m/s

Pressure:≤70mpa

SRDF Piston Rod Seal

Material

Polyester rubber

Temperature:-40`100℃

Speed:=1.0m/s

SDY Y-seal

Material:Polyurethane

Temperature:-35~110℃

Speed:=0.5m/s

Pressure:≤70mpa

KZT anti fouling ring

SDS Steffel

Piston main oil seal

oil seals,hydraulic oil seal,track link oil seal,TCV oil seal,O-ring

Safe Seal Technology Co., Ltd. , https://www.aprseal.com